WiFi - Connect to WiFi

Materials

AmebaPro2 [ AMB82 MINI ] x 1

Procedure

There three common encryption type in WiFi connection. The first one is “OPEN”, which means there is no password needed to connect to this network. The second type of encryption is WPA, which requires the correct password to access. The third type is WEP, which requires a hexadecimal password and a keyindex.

In the following, we will give a brief introduction on how to establish WiFi connection with these three types of encryptions on Ameba.

First, make sure the correct Ameba development board is selected in “Tools” -> “Board”.

Open (WiFi connection without password)

Open example in “File” -> “Examples” -> “WiFi” -> “ConnectToWiFi” -> “NoEncryption”

In the sample code, modify “ssid” to be the same as the WiFi SSID to be connected to.

Next, upload the sample code, and press the reset button on Ameba. Then you will see a message “You’re connected to the networkSSID: XXXXX”, and the information of this WiFi connection is printed in the serial monitor every 10 seconds.

WiFi connection with WPA encryption

Open example in “File” -> “Examples” -> “WiFi” -> “ConnectToWiFi” -> “WPA_Security”

In the sample code, modify “ssid” to the WiFi SSID to be connected to and “pass” to the network password.

If you prefer to enter your SSID & password in the Serial monitor while the program is running, uncomment #define MANUAL_INPUT at the top of the file.

Note: If you enabled MANUAL_INPUT, after uploading the sample code and pressing the reset button on Ameba, input your SSID in the Serial monitor and press enter. Next, input your password, and press enter. Then you will see a message “You’re connected to the networkSSID: XXXXX”, and the information of this WiFi connection is printed in the serial monitor every 10 seconds.

WiFi connection with WEP encryption

Open example in “File” -> “Examples” -> “WiFi” -> “ConnectToWiFi” -> “WEP_Security”

In the sample code, modify “ssid” to the SSID to be connected, “key” to the hexadecimal password, “keyIndex” to your key index number.

If you prefer to enter your SSID & password in the Serial monitor while the program is running, uncomment #define MANUAL_INPUT at the top of the file.

Note: If you enabled MANUAL_INPUT, after uploading the sample code and pressing the reset button on Ameba, input your SSID in the Serial monitor and press enter. Next, input your key and press enter. Finally enter your password and press enter. Then you will see a message “You’re connected to the networkSSID: XXXXX”, and the information of this WiFi connection is printed in the serial monitor every 10 seconds.

Code Reference

https://www.arduino.cc/en/Reference/WiFiBegin
To get the information of a WiFi connection:
Use WiFi.SSID() to get SSID of the current connected network.
https://www.arduino.cc/en/Reference/WiFiSSID
Use WiFi.RSSI() to get the signal strength of the connection.
https://www.arduino.cc/en/Reference/WiFiRSSI
Use WiFi.encryptionType() to get the encryption type of the WiFi connection.
https://www.arduino.cc/en/Reference/WiFiEncryptionType
Use WiFi.BSSID() to get the MAC address of the router you are connected to.
https://www.arduino.cc/en/Reference/WiFiBSSID
To get the information of Ameba:
Use WiFi.macAddress() to get the MAC address of Ameba.
https://www.arduino.cc/en/Reference/WiFiMACAddress
Use WiFi.localIP() to get the IP address of Ameba.
https://www.arduino.cc/en/Reference/WiFiLocalIP
Use WiFi.subnetMask() to get the subnet mask.
https://www.arduino.cc/en/Reference/WiFiSubnetMask
Use WiFi.gatewayIP() to get the WiFi shield’s gateway IP address.
https://www.arduino.cc/en/Reference/WiFiGatewayIP

Comparison with Arduino

In the Arduino platform, we need to add an extra WiFi shield to be the WiFi module to realize the WiFi connection. And we must #include to use SPI to communicate with WiFi module.
However, Ameba is already equipped with WiFi module. Therefore, #include is not needed.

WiFi - Connect to WiFi

Solutions

Developers

Cloud Service

Forums

Related Sites